WoodWorkingLand

Best 10 Inch Table Saw Blade In The Market Today


It may seem like all 10” table saw blades are the same, but as they say, the devil is in the details.


Here, we break it down piece by piece in order for you to choose the best blade for the job.


There is a wide array of options to choose from, ranging from cross cutting blades to ripping blades to combination blades and even sets of blades.

Take a look below to learn more about table saw blade types and our recommendations for what to pick for your next project! 

Common Table Saw Blade Types


The distinguishing factor of the five common types of blades is the geometry of the blade teeth.


The five kinds of blades include the Flat Top Grind Blade (FTG), the Alternate Top Bevel Blade (ATB), the High- Angle Alternate Top Bevel Blade (Hi-ATB), Combination Blades, and Triple Chip Grind Blade (TCG).

Like the name suggests, FTG blades have teeth with flat edges that run parallel to the edge of the plate.


This type of blade is most optimal for rip cutting, where efficiency is more valuable than the quality of the cut.


FTG blades cut with the grain of the wood with teeth called rakers.


They attack the material agressively, which may leave some chipping or splintered edges.


Opposite to the FTG blade, ATB blades have two different sets of teeth that tilt in opposing directions.


This type of blade is most appropriate for cross cutting, which cuts perpendicular to the grain of wood.


Having two sets of teeth allows for scoring, making the cuts less likely to chip the material.


Very similar to ATB blades, Hi-ATB blades have teeth with steeper angles that are critical for an ultra-smooth cross cut. Since it has a high bevel angle, this type of teeth also dulls quickly.


The most common blade is the combination blade, which incorporates ATB teeth and FTG teeth.


This blade is able to cross cut and rip cut, making it a great multi-use option.


Like a combination blade, TCG blades also combine two different sets of teeth.


It consists of flat top teeth for easy ripping, and another modified TCG blade that has sloped edges that make the blade less likely to dull. 

Does Size Matter?


Table saw blades are always measured by their diameters. It is easy to forget that the maximum depth for a table saw blade is only the saw’s radius.


The actual size that the blade is able to cut should be measured from the bottom of the gullets (rounded space between teeth) to the edge of the anchor hole in the middle.


The most common size is 10 inches, but you can consider buying a larger or smaller blade depending on the material you will be cutting.


Some may choose to go for a smaller blade for reduced waste or kickback; however, the depth of the cut is lost. 


A helpful tip is to never choose a larger blade than needed, since it will require more power and exhaust the engine leading to decreased blade life.

Number of Teeth


Blades differ in the amount of teeth depending on what type of work they are designed to do.


The number of teeth on a table saw can range anywhere from 25 to 90 teeth.


Blades with fewer teeth are most optimal for rip cutting while blades with a higher tooth count are generally used for cross cutting. 


People that use their blades for different materials often choose a combination blade that has an average number of teeth.

Angle of Teeth Hooks


The angle that is most optimal for cutting metals and harder materials is a Zero Hook Angle.


This is where the blade’s flat edge of the tooth lines up with the diameter of the blade.


A positive hook angle is angled with the direction the blade rotates ensuring a quicker rate.


This means a more aggressive and quicker cut.


A negative hook angle is angled away from the direction the blade rotates, which prevents chipping and an overly quick cut.


This gives the user more control and ensures a cleaner cut.

Picking the Best Blade for the Job


  • Ripping: A thin kerf (width) FTG blade ranging from 20-40 teeth is best. A lower range of teeth and a thin width can ensure efficiency and lessen the strain on your saw even while making aggressive cuts.
  • Cross-Cutting: A combination blade or an ATB blade ranging anywhere from 40-90 teeth work best. The teeth on these blades ensures a cleaner cut.
  • Joinery: ATB or combination blades work best, since this work requires a clean edge for attaching.
  • Plastic and Metal: TCG blades are best, since they are able to slice through denser materials more easily. Combination blades may work, but are more likely to dull faster. 

Maintenance


Proper care of your 10 inch saw blade can extend the life of your table saw blade by a considerable amount.


Much like a razor blade, dull and dirty table saw blades could result in uneven cuts.

Our Top Picks for 10 in. Table Saw Blades


TOP RATED

TOP RATED

TOP RATED

Freud 10 x 80T Ultimate Plywood

Freud 10" Blade

Overpeak 10'' Cutting Saw

This 10-inch Overpeak saw has 90 Alternate Top Bevel teeth that is optimized for clean and effortless cross cutting.


It saws through touch material like butter with its slightly negative hook angle.


A unique feature of this blade is the four-sided grind which ensures every side of the cut is smooth without needing any extra sanding or smoothing of the material.


 It also works with different types of saws making this a great tool to have on hand. The high number of teeth makes an extra-fine cut, but also works for ripping as well.

The blade is also made with tungsten carbide, which is a great feature to have, especially for a blade with a high number of teeth.


This characteristic ensures that the blade will not warp or dull quickly even while keeping the high quality of cuts.


We tested this blade on a large range of materials, and did not chip even the more brittle materials. This is a great blade for ultra- fine cuts.

Pros

  • Very durable for longer-lasting performance
  • Laser-like cuts allow you to get down into the details
  • Versatile usability

Cons

  • Slow rate
  • Subtle vibrations may throw some people off
  • Wider width

Luckyway 2-pack 10" Blades

The Luckyway 10- inch blade pack comes with a 32- tooth and 60-tooth ATB blade. This pack allows for versatility since you are able to choose between a lower and higher tooth count.


These blades also work for both cross cutting and ripping.


These blades are most optimized for hard and soft woods, but less optimal or other materials.


They are made with manganese with tungsten carbide teeth to ensure a longer lasting blade.


These blades are great for a wide range of uses without any splintering of the material.

Another great feature of this blade is that it is able to cut through any nails in the wood.


The teeth are coated with tungsten carbide which helps to maintain the sharpness of the blade and also keeps the blade from overheating.


The Luckway blade is a great buy especially for the price.


The positive tooth angle ensures for a clean and efficient cut. 

Pros

  • Great value for money
  • Able to make different types of cuts
  • Works on different saws

Cons

  • Slight wobble
  • Needs to be sharpened out of the box

DEWALT 10" Blade

This Dewalt pack also comes with two different 10-inch blades.


One is a 32-tooth blade for general purpose cutting and another 60-tooth blade for crosscutting.


This pack is a great value, especially if you are looking to build your toolkit.


A distinguishing feature of this blade is the thin width, which allows for efficient cutting as well as minimum waste.


This pack is suitable for cutting a wide range of materials including hardwood, softwood, easy to chip materials, and plywood.


These Dewalt blades also have an added steel piece on the back of each tooth to ensure the most precise and strong cut.

After testing, we can ensure that this is a heavy-duty blade that can assist you on a wide array of tasks.


Another notable feature is that the blade is computer-balanced which effectively reduces the vibration of the blade while working.


This adds to the longevity of these blades as well as the accuracy of the cut. 

Pros

  • Multifaceted
  • No vibrations
  • Durable

Cons

  • Loud
  • Coarse blade
  • Not as suitable for extra hard woods

Mastec 10" Blade

This Mastec 10-inch blade is equipped with 80 ATB teeth used for finer cuts.


The ATB blade is most suitable for cutting different types of wood.


A notable feature of this blade is that it is able to be used by a wide range of different types of saws.


Having a higher number of teeth leaves an ultra-fine cut that usually leads to a slower feed rate;


however, this blade is able to cut efficiently and effortlessly even keeping the accuracy of the cut. 


The non-stick coating reduces the buildup that usually occurs with these types of ATB blades.


This is a great blade for beginners since it also has a useful anti-kickback feature that boosts the safety of this blade.


Table Saw Safety Rules You Should Know

Sawing can be daunting to beginners, but having this safety feature can help you feel more comfortable cutting.


This blade is also a great value for the quality of cut you are going to get. 

Pros

  • Affordable for those who are just getting into using table saws or want to save a bit more money
  • Able to rip cut as well
  • No drag

Cons

  • Less durable
  • Lightweight

Freud 10" Blade

This Freud 10-inch blade is a thin kerf Hi-ATB blade that works best on cutting melamine and plywood.


It is a high quality blade that creates extra clean cross cuts.


The high bevel angle ensures a chip-free surface, even on materials that chip easily.


An added advantage of this blade that sets it apart from others is the laser-cut anit-vibration cutouts that make sure the blade runs straight without any wobble.


Since this blade is made for sharp and accurate cuts, this is an extremely important factor. 


Not only does this help with the vibration of the blade, it also runs the blade extremely quietly, which is a great bonus.

The thin kerf also allows the blade to run more smoothly and at a faster feed rate, even with a higher tooth count.


With this blade, there is no need to sacrifice speed for exquisite, accurate cuts.


The high bevel helps to score the cut before making the cut, ensuring the blade’s accuracy.


If you are looking for a great blade with accuracy as a priority, this is the one for you. 

Pros

  • No tear-out
  • Extremely accurate
  • Great for easy to chip woods

Cons

  • Mainly used for cross cuts
  • Required sharpening maintenance

Freud 10" x 30T Blade

The Freud 10-inch blade has 30 TCG teeth with a thin kerf for faster rip cutting. This blade is designed mainly for rip cutting with its low number of teeth.


Its ideal cutting range is from ⅛” to 1”, even though it may work for others outside the range as well.


The triple chip tooth grind smooths the cutting material, which requires no extra sanding.


This design ensures smooth cuts, even with a ripping blade, which is perfect for finishing work that requires smooth surfaces.


The blade is extra thin which requires less energy to run, without compromising the quality of the cut.

This is a great choice for those that know exactly what type of work they will be doing.


Since it is a ripping blade, the teeth usually dull quickly, but the HI- density Carbide tips keep the blade sharp for longer maximizing the use.


If you are looking to add a high quality ripping blade to your arsenal, look no further. 

Pros

  • Quiet and can be used without worrying about noise
  • Perfectly parallel
  • Efficient

Cons

  • Mainly used for rip cutting
  • Requires sanding
  • Needs sharpening

Conclusion


Looking for the best 10-inch saw blade can seem daunting at first glance because of all the options, but hopefully we helped you narrow down your choices.


Our top pick for the best 10” table saw blade is the Overpeak 10-in x 90T ATB blade.


This blade can be used for both cross cutting and rip cutting, but has great precision at an affordable price.


You do not have to sacrifice efficiency, speed, or durability with this saw.


This is a blade that would be a great addition to everyone’s toolkit.


With the wide range of table saw blades you will be sure to find the right one for you!

Woodworking Tips You Should Know
Get It Now for Free